[ 0.000000] Linux version 5.4.109 (julius@elleboog) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16453-497edc412a)) #0 SMP Tue Apr 6 07:53:16 2021 [ 0.000000] SoC: xRX200 rev 1.2 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019556 (MIPS 34Kc) [ 0.000000] MIPS: machine is AVM FRITZ!Box 7490 [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Detected 1 available secondary CPU(s) [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000] On node 0 totalpages: 65536 [ 0.000000] Normal zone: 576 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 65536 pages, LIFO batch:15 [ 0.000000] percpu: Embedded 14 pages/cpu s26224 r8192 d22928 u57344 [ 0.000000] pcpu-alloc: s26224 r8192 d22928 u57344 alloc=14*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960 [ 0.000000] Kernel command line: console=ttyLTQ0,115200 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Writing ErrCtl register=000098c0 [ 0.000000] Readback ErrCtl register=000098c0 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 250300K/262144K available (5935K kernel code, 210K rwdata, 1528K rodata, 1268K init, 207K bss, 11844K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] NR_IRQS: 256 [ 0.000000] random: get_random_bytes called from start_kernel+0x318/0x530 with crng_init=0 [ 0.000000] CPU Clock: 500MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041786 ns [ 0.000011] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every 8589934590ns [ 0.007911] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088) [ 0.045972] pid_max: default: 32768 minimum: 301 [ 0.050926] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.058128] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.069537] rcu: Hierarchical SRCU implementation. [ 0.075125] smp: Bringing up secondary CPUs ... [ 0.080846] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.080865] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.080970] CPU1 revision is: 00019556 (MIPS 34Kc) [ 0.111799] Synchronize counters for CPU 1: done. [ 0.136198] smp: Brought up 1 node, 2 CPUs [ 0.146889] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.156547] futex hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.163577] pinctrl core: initialized pinctrl subsystem [ 0.170840] NET: Registered protocol family 16 [ 0.190339] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV [ 0.203542] GPIO line 484 (pcie-rst-dev) hogged as output/low [ 0.209235] GPIO line 467 (wasp-wakeup) hogged as output/high [ 0.215035] GPIO line 476 (usb-power) hogged as output/high [ 0.221135] pinctrl-xway 1e100b10.pinmux: Init done [ 0.227789] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28 [ 0.239378] PCI host bridge /fpi@10000000/pci@e105400 ranges: [ 0.245063] MEM 0x0000000018000000..0x0000000019ffffff [ 0.250324] IO 0x000000001ae00000..0x000000001affffff [ 0.299287] usbcore: registered new interface driver usbfs [ 0.304920] usbcore: registered new interface driver hub [ 0.310461] usbcore: registered new device driver usb [ 0.316277] PCI host bridge to bus 0000:00 [ 0.320317] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff] [ 0.327228] pci_bus 0000:00: root bus resource [io 0x1ae00000-0x1affffff] [ 0.334188] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.341009] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.351715] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 0.358396] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512 [ 0.371388] clocksource: Switched to clocksource MIPS [ 0.378181] NET: Registered protocol family 2 [ 0.384111] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.392424] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.400135] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.407348] TCP: Hash tables configured (established 2048 bind 2048) [ 0.413915] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.420385] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.427790] NET: Registered protocol family 1 [ 0.432094] PCI: CLS 0 bytes, default 32 [ 0.436899] gptu: totally 6 16-bit timers/counters [ 0.441865] gptu: misc_register on minor 63 [ 0.446063] gptu: succeeded to request irq 126 [ 0.450541] gptu: succeeded to request irq 127 [ 0.455058] gptu: succeeded to request irq 128 [ 0.459554] gptu: succeeded to request irq 129 [ 0.464100] gptu: succeeded to request irq 130 [ 0.468580] gptu: succeeded to request irq 131 [ 0.473279] No VPEs reserved for AP/SP, not initialize VPE loader [ 0.473279] Pass maxvpes= argument as kernel argument [ 0.484657] No TCs reserved for AP/SP, not initializing RTLX. [ 0.484657] Pass maxtcs= argument as kernel argument [ 0.498260] workingset: timestamp_bits=14 max_order=16 bucket_order=2 [ 0.523381] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.529198] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.539192] random: fast init done [ 0.550758] gpio-export gpio-export: 1 gpio(s) exported [ 0.559788] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc [ 0.568707] printk: console [ttyLTQ0] enabled [ 0.577444] printk: bootconsole [early0] disabled [ 0.590220] nand: device found, Manufacturer ID: 0x98, Chip ID: 0xdc [ 0.595143] nand: Toshiba NAND 512MiB 3,3V 8-bit [ 0.599752] nand: 512 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 128 [ 0.607573] Scanning device for bad blocks [ 0.861096] Bad eraseblock 1536 at 0x000018000000 [ 0.864499] Bad eraseblock 1537 at 0x000018040000 [ 0.951816] 2 fixed-partitions partitions found on MTD device 14000000.flash [ 0.957447] Creating 2 MTD partitions on "14000000.flash": [ 0.962942] 0x000000000000-0x000000400000 : "kernel" [ 0.970193] 0x000000400000-0x000020000000 : "ubi" [ 0.980535] spi-lantiq-ssc 1e100800.spi: Lantiq SSC SPI controller (Rev 8, TXFS 8, RXFS 8, DMA 1) [ 0.990784] spi-nor spi0.4: mx25l8005 (1024 Kbytes) [ 0.994325] 3 fixed-partitions partitions found on MTD device spi0.4 [ 1.000623] Creating 3 MTD partitions on "spi0.4": [ 1.005417] 0x000000000000-0x000000040000 : "urlader" [ 1.012785] 0x000000040000-0x0000000a0000 : "tffs (1)" [ 1.018835] 0x0000000a0000-0x000000100000 : "tffs (2)" [ 1.026606] libphy: Fixed MDIO Bus: probed [ 1.040268] NET: Registered protocol family 10 [ 1.048000] Segment Routing with IPv6 [ 1.050335] NET: Registered protocol family 17 [ 1.054911] 8021q: 802.1Q VLAN Support v1.8 [ 1.065459] pcie-xrx200 1d900000.pcie: failed to get the PCIe PHY [ 1.075516] RING initilized [ 1.178832] libphy: lantiq,xrx200-mdio: probed [ 1.181958] mdio_bus 0: MDIO device at address 0 is missing. [ 1.187607] mdio_bus 0: MDIO device at address 1 is missing. [ 1.193226] mdio_bus 0: MDIO device at address 17 is missing. [ 1.199006] mdio_bus 0: MDIO device at address 19 is missing. [ 1.205652] Static link. Port <0>! [ 1.209006] Registered fixed-link [ 1.211562] lantiq,xrx200-net 1e108000.eth eth0 (uninitialized): Connect as fixed link. [ 1.219607] Generic PHY fixed-0:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:00, irq=POLL) [ 1.229388] lantiq,xrx200-net 1e108000.eth eth0 (uninitialized): no PHY found [ 1.236466] lantiq,xrx200-net 1e108000.eth eth0 (uninitialized): xrx200-mdio: probing phy of port 4 failed [ 1.246127] lantiq,xrx200-net 1e108000.eth eth0 (uninitialized): no PHY found [ 1.253264] lantiq,xrx200-net 1e108000.eth eth0 (uninitialized): xrx200-mdio: probing phy of port 2 failed [ 1.262927] lantiq,xrx200-net 1e108000.eth eth0 (uninitialized): no PHY found [ 1.270063] lantiq,xrx200-net 1e108000.eth eth0 (uninitialized): xrx200-mdio: probing phy of port 1 failed [ 1.279709] lantiq,xrx200-net 1e108000.eth eth0 (uninitialized): no PHY found [ 1.286860] lantiq,xrx200-net 1e108000.eth eth0 (uninitialized): xrx200-mdio: probing phy of port 0 failed [ 1.298471] WAN map = 0000 [ 1.435117] PCI host bridge /fpi@10000000/pcie@d900000 ranges: [ 1.439863] PCI host bridge to bus 0000:01 [ 1.443717] pci_bus 0000:01: root bus resource [mem 0x1c000000-0x1cffffff] [ 1.450606] pci_bus 0000:01: root bus resource [io 0x1d800000-0x1d8fffff] [ 1.457474] pci_bus 0000:01: root bus resource [??? 0x00000000 flags 0x0] [ 1.464257] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff] [ 1.472238] pci 0000:01:00.0: [1bef:0011] type 01 class 0x060000 [ 1.478173] ifx_pcie_rc_class_early_fixup: fixed pcie host bridge to pci-pci bridge [ 1.496006] pci 0000:01:00.0: ifx_pcie_rc_class_early_fixup+0x0/0x7c took 17370 usecs [ 1.502566] pci 0000:01:00.0: PME# supported from D0 D3hot [ 1.511214] pci 0000:01:00.0: bridge configuration invalid ([bus 02-00]), reconfiguring [ 1.518189] pci 0000:02:00.0: [1912:0015] type 00 class 0x0c0330 [ 1.523955] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit] [ 1.530871] pci 0000:02:00.0: PME# supported from D0 D3hot [ 1.536185] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:01:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link) [ 1.553247] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 1.558505] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 02 [ 1.565116] pci 0000:01:00.0: BAR 8: assigned [mem 0x1c000000-0x1c0fffff] [ 1.571895] pci 0000:02:00.0: BAR 0: assigned [mem 0x1c000000-0x1c001fff 64bit] [ 1.579244] pci 0000:01:00.0: PCI bridge to [bus 02] [ 1.584168] pci 0000:01:00.0: bridge window [mem 0x1c000000-0x1c0fffff] [ 1.591079] ifx_pcie_bios_map_irq port 0 dev 0000:01:00.0 slot 0 pin 1 [ 1.597537] ifx_pcie_bios_map_irq dev 0000:01:00.0 irq 144 assigned [ 1.603831] pcieport 0000:01:00.0: enabling device (0000 -> 0002) [ 1.610570] pci 0000:02:00.0: enabling device (0000 -> 0002) [ 1.621500] pci 0000:02:00.0: xHCI HW not ready after 5 sec (HC bug?) status = 0x801 [ 1.627894] pci 0000:02:00.0: quirk_usb_early_handoff+0x0/0x7f0 took 16926 usecs [ 1.636168] UBI: auto-attach mtd1 [ 1.638522] ubi0: attaching mtd1 [ 1.944179] ubi0: scanning is finished [ 1.964455] ubi0: attached mtd1 (name "ubi", size 508 MiB) [ 1.968581] ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 258048 bytes [ 1.975429] ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 1024 [ 1.982187] ubi0: VID header offset: 1024 (aligned 1024), data offset: 4096 [ 1.989155] ubi0: good PEBs: 2030, bad PEBs: 2, corrupted PEBs: 0 [ 1.995251] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 2.002490] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 387497449 [ 2.011526] ubi0: available PEBs: 0, total reserved PEBs: 2030, PEBs reserved for bad PEB handling: 38 [ 2.020905] ubi0: background thread "ubi_bgt0d" started, PID 464 [ 2.026911] block ubiblock0_0: created from ubi0:0(rootfs) [ 2.026929] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem [ 2.048173] VFS: Mounted root (squashfs filesystem) readonly on device 259:0. [ 2.055987] Freeing unused kernel memory: 1268K [ 2.059058] This architecture does not have kernel memory protection. [ 2.065559] Run /sbin/init as init process [ 2.713806] init: Console is alive [ 2.716257] init: - watchdog - [ 3.266891] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.396820] ifx_pcie_bios_map_irq port 0 dev 0000:02:00.0 slot 0 pin 1 [ 3.402119] ifx_pcie_bios_map_irq dev 0000:02:00.0 irq 144 assigned [ 3.408558] xhci_hcd 0000:02:00.0: xHCI Host Controller [ 3.413611] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 1 [ 13.421005] xhci_hcd 0000:02:00.0: can't setup: -145 [ 13.424601] xhci_hcd 0000:02:00.0: USB bus 1 deregistered [ 13.430051] xhci_hcd 0000:02:00.0: init 0000:02:00.0 fail, -145 [ 13.435927] xhci_hcd: probe of 0000:02:00.0 failed with error -145 [ 13.444607] ifx_pcie_bios_map_irq port 0 dev 0000:02:00.0 slot 0 pin 1 [ 13.449930] ifx_pcie_bios_map_irq dev 0000:02:00.0 irq 144 assigned [ 13.466965] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 13.484011] init: - preinit - [ 14.296923] renesas xhci 0000:02:00.0: xHCI Host Controller [ 14.301242] renesas xhci 0000:02:00.0: new USB bus registered, assigned bus number 1 [ 14.314550] renesas xhci 0000:02:00.0: hcc params 0x014051cf hci version 0x100 quirks 0x0000000101000090 [ 14.324560] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04 [ 14.331496] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 14.338759] usb usb1: Product: xHCI Host Controller [ 14.343577] usb usb1: Manufacturer: Linux 5.4.109 xhci-hcd [ 14.349076] usb usb1: SerialNumber: 0000:02:00.0 [ 14.355037] hub 1-0:1.0: USB hub found [ 14.357618] hub 1-0:1.0: 2 ports detected [ 14.363028] renesas xhci 0000:02:00.0: xHCI Host Controller [ 14.367282] renesas xhci 0000:02:00.0: new USB bus registered, assigned bus number 2 [ 14.375042] renesas xhci 0000:02:00.0: Host supports USB 3.0 SuperSpeed [ 14.382036] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 14.390302] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.04 [ 14.397985] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 14.405194] usb usb2: Product: xHCI Host Controller [ 14.410042] usb usb2: Manufacturer: Linux 5.4.109 xhci-hcd [ 14.415531] usb usb2: SerialNumber: 0000:02:00.0 [ 14.421406] hub 2-0:1.0: USB hub found [ 14.427334] hub 2-0:1.0: 2 ports detected [ 14.588985] random: procd: uninitialized urandom read (4 bytes read) [ 15.013820] a1 [ 15.014020] a2 [ 15.015725] a3 [ 15.017322] a4 [ 15.018975] a5 [ 15.020665] a2 [ 15.022283] a3 [ 15.023991] a4 [ 15.025591] a5 [ 15.027310] b1 [ 15.028900] b2 [ 15.030552] b2 [ 15.033065] lantiq,xrx200-net 1e108000.eth eth0: port 5 got link [ 15.038588] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 19.333307] UBIFS (ubi0:1): default file-system created [ 19.338067] UBIFS (ubi0:1): Mounting in unauthenticated mode [ 19.343305] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 551 [ 19.499765] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 19.506249] UBIFS (ubi0:1): LEB size: 258048 bytes (252 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes [ 19.516151] UBIFS (ubi0:1): FS size: 501903360 bytes (478 MiB, 1945 LEBs), journal size 25030656 bytes (23 MiB, 97 LEBs) [ 19.527013] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB) [ 19.533635] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 66045C27-4CA9-4B71-A216-4FDBB426411B, small LPT model [ 19.547078] mount_root: overlay filesystem has not been fully initialized yet [ 19.553613] mount_root: switching to ubifs overlay [ 19.565808] urandom-seed: Seed file not found (/etc/urandom.seed) [ 19.706043] lantiq,xrx200-net 1e108000.eth eth0: port 5 lost link [ 19.726101] procd: - early - [ 19.727872] procd: - watchdog - [ 20.385889] procd: - watchdog - [ 20.388689] procd: - ubus - [ 20.470226] random: ubusd: uninitialized urandom read (4 bytes read) [ 20.477036] random: ubusd: uninitialized urandom read (4 bytes read) [ 20.482713] random: ubusd: uninitialized urandom read (4 bytes read) [ 20.495333] procd: - init - [ 21.732922] kmodloader: loading kernel modules from /etc/modules.d/* [ 21.743565] IFXOS, Version 1.5.19 (c) Copyright 2009, Lantiq Deutschland GmbH [ 21.755510] NET: Registered protocol family 8 [ 21.758413] NET: Registered protocol family 20 [ 21.773494] PPP generic driver version 2.4.2 [ 21.819034] Lantiq (VRX) DSL CPE MEI driver, version 1.5.17.6, (c) 2007-2015 Lantiq Beteiligungs-GmbH & Co. KG [ 21.835489] [ 21.835489] [ 21.835489] Lantiq CPE API Driver version: DSL CPE API V4.17.18.6 [ 21.853197] [ 21.853197] Predefined debug level: 3 [ 21.877944] Infineon Technologies DEU driver version 2.0.0 [ 21.885455] IFX DEU DES initialized (multiblock). [ 21.891578] IFX DEU AES initialized (multiblock). [ 21.895994] IFX DEU ARC4 initialized (multiblock). [ 21.900304] IFX DEU SHA1 initialized. [ 21.903907] IFX DEU MD5 initialized. [ 21.907560] IFX DEU SHA1_HMAC initialized. [ 21.911613] IFX DEU MD5_HMAC initialized. [ 21.928763] NET: Registered protocol family 24 [ 21.948006] xt_time: kernel timezone is -0000 [ 22.000055] kmodloader: done loading kernel modules from /etc/modules.d/* [ 22.143451] urngd: v1.0.2 started. [ 22.377581] random: crng init done [ 22.379611] random: 6 urandom warning(s) missed due to ratelimiting [ 61.755117] set vlan portmap [ 64.842628] a1 [ 64.842841] a2 [ 64.844658] a3 [ 64.846160] a4 [ 64.847926] a5 [ 64.849460] a2 [ 64.851116] a3 [ 64.852782] a4 [ 64.854439] a5 [ 64.856201] b1 [ 64.857742] b2 [ 64.859488] b2 [ 64.879812] lantiq,xrx200-net 1e108000.eth eth0: port 5 got link [ 64.885173] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 64.925800] device eth0 entered promiscuous mode [ 64.930793] br-lan: port 1(eth0.1) entered blocking state [ 64.934916] br-lan: port 1(eth0.1) entered disabled state [ 64.941039] device eth0.1 entered promiscuous mode [ 64.990473] br-lan: port 1(eth0.1) entered blocking state [ 64.994530] br-lan: port 1(eth0.1) entered forwarding state [ 65.828071] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready